Noco GB40 Mavuto: Ngati mukukumana ndi mavuto ndi Noco GB40 kulumpha sitata, pali njira zingapo zomwe mungayesere. Onetsetsani kuti batire yanu yayikidwa bwino. Batire iyenera kuyikidwa pansi pa unit ndipo zolumikizira zasiliva pa batire ziyenera kulumikizidwa ndi zolumikizira zasiliva pa unit..
Wamba NOCO GB40 Jump Starter Mavuto
- Not Charging
- Not Working
- Clicking Noise
- Flashing Red & Green
- The chords on clamps are very short
- Lack of a wall charger for recharging
- Restricted to 12-volt lead-acid batteries
- Limited capacity and number of ports
- Only has 5V ports
- Jump-starts for less than six times
- Lights keep running
Not Charging and Solution
Not Charging: Ngati Noco Genius Boost GB40 yanu siyikulipira, chifukwa chotheka ndi batire kapena charger. Ngati mwayesa ma charger osiyanasiyana ndi mabatire, ndiye vuto likhoza kukhala ndi chipangizocho chokha.
Kukonza izi, remove any loose objects near the device or try pressing down on the speaker until it disappears. If you are hearing clicking noises from your Noco Genius Boost GB40, zikhoza kukhala kuti pali chinachake chimene chikulepheretsa wokamba nkhaniyo.
Not Working and Solution
Konzani osalipira: Ngati Noco GB40 Genius Boost yanu siyikulipira bwino, yesani kusintha batire. Ngati izo sizithetsa vuto, zitha kukhala chifukwa cha charger yolakwika. Zikatero, please reach out to our support team for a replacement charger.
Clicking Noise and Solution
Oyamba kudumpha ena amapanga phokoso lakuthwa akamalipira. Izi nthawi zambiri zimakhala chifukwa batire imakhala yozizira kwambiri kapena yotentha kwambiri. Kukonza vutoli, tenthetsani batire musanayese kulitchaja. Kapenanso, yesani kugwiritsa ntchito mtundu wina wa charger poyambira.
Flashing Red & Green ndi Solution
If your NOCO GB40 is flashing red and green, pali zinthu zingapo zomwe mungachite kuti muyese kukonza vutoli. Choyamba, check the battery level and make sure it is charged. Ngati batire ili yochepa, charge it for a few hours and then try again. Ngati batire ili ndi mlandu, try resetting the device by pressing and holding the power button for 10 masekondi. If the GB40 still won’t stop flashing red and green, contact NOCO customer support for help.
The chords on clamps are very short
Your NOCO GB40 chords on clamps are very short, there are a few things you can do to fix the issue. Choyamba, try to adjust the clamps so that they are not so tight. This will give the chords some slack and allow you to stretch them out a bit. Ngati izi sizikugwira ntchito, you can try using a wire cutter to cut the chords. Be sure to cut them as close to the clamps as possible so that you do not damage the clamps.
Lack of a wall charger for recharging
Because of your NOCO GB40 jump starter doesn’t come with a wall charger, you can use a USB cable to recharge it. Just connect the USB cable to the GB40 and then plug it into a USB power source. You can use a USB port on your computer or a USB power adapter.
It’s also important to make sure that the GB40 is properly connected to the power source. The red charging indicator light should be lit up when the GB40 is connected to a power source. If the red light is not lit, check the connections and make sure that the GB40 is properly plugged into the power source.
Once the GB40 is properly connected to a power source, the red charging indicator light will turn off when the GB40 is fully charged.
Restricted to 12-volt lead-acid batteries
Choyamba, you’ll want to check the battery terminals to make sure that they are clean and free of corrosion. If the terminals are corroded, you can clean them with a wire brush or by using a solution of baking soda and water.
Ena, you’ll want to check the connections between the charger and the battery. Make sure that the connections are tight and secure.
Pomaliza, you’ll want to check the charger itself to make sure that it is working properly. If the charger is not working properly, mungafunike kusintha.
Limited capacity and number of ports
Choyamba, try resetting the device. Kuchita izi, simply remove the battery and then reinsert it. This should reset the device and hopefully fix the issue.
Ngati izo sizigwira ntchito, then you may need to update the firmware on the device. You can do this by downloading the latest firmware from the NOCO website and then following the instructions on how to update the firmware.
If neither of those solutions work, then you may need to contact NOCO customer support for further assistance.
Only has 5V ports
Choyamba, check to make sure that the charging cable is properly connected to the GB40. If the cable is loose or not properly connected, this could be the reason why the GB40 is only outputting 5V.
Ena, try resetting the GB40 by disconnecting it from the power source and then reconnecting it. This sometimes helps to reset the unit and fix any issues that may be causing it to only output 5V.
Jump-starts for less than six times
Choyamba, fufuzani batire. Make sure that it is properly charged and that there are no loose connections.
If the battery seems to be fine, then the next step is to check the jump-start terminals. Make sure that they are clean and free of corrosion.
If the terminals are clean and the battery is charged, then the next step is to check the jumper cables. Make sure that they are the right size and that they are in good condition.
If the jumper cables are in good condition and the right size, then the next step is to check the engine. Make sure that there is no debris blocking the engine from starting.
If the engine is clear and the battery is charged, then the last step is to check the NOCO GB40 itself. Make sure that it is properly connected and that all of the settings are correct.
Lights keep running
Choyamba, check the batteries. If the batteries are low, recharge them or replace them with new ones. If the batteries are not the problem, then the issue may be with the light itself. Try cleaning the light with a soft cloth and see if that helps. If the light is still not working properly, mungafunike kusintha.
FAQ
Q1: Kodi ndimagwiritsa ntchito bwanji Noco Genius Boost GB40?
Q2: Kodi Noco GB40 imakhala nthawi yayitali bwanji??
The NOCO GB40’s can last a very long time due to the cycle capabilities of the lithium battery, the key is to charge them once every 6 months if they are in storage.
Q3: Kodi Noco GB40 imalipira batire?
Inde, the Noco GB40 will charge your battery. It is a battery charger and maintainer that is designed to keep your battery charged and in good condition.
Q4: Kodi ndimalipira bwanji Genius GB40?
Q5: Kodi Noco GB40 iyenera kulipiritsidwa kwathunthu?
Inde, when you get it, fully charge it before first using it to ensure optimal performance.
Q6: Kodi ndingasiye NOCO boost kuphatikiza gb40 yolumikizidwa?
Inde, the NOCO GB40 has built in overcharge protection and can remain on a charging source at all times.
Q7: Kodi ndingadziwe bwanji ngati Noco genius akulipira?
Pamene batire ikulipira, the charge LED will be illuminated red. The charge LED will remain a solid Red color (not blinking) until the battery is fully charged. Pamene batire yadzaza kwathunthu, the charge LED will be illuminated Green.
Q8: How do I reset a Noco GB40 Battery charger?
Pali njira zingapo zosinthira chojambulira cha Noco GB40. Anthu ena amapeza kuti akuyenera kuchita izi pomwe chojambulira chawo sichikulipira chipangizo chawo kapena pomwe akupeza phokoso kuchokera pa charger..
Chotsani batire ndi memori khadi ku chipangizo. Zimitsani charger pakhoma. Chotsani batire ndi memori khadi ku chipangizo. Dinani batani lamphamvu kuti 3 masekondi, kenako chotsani batire ndi memori khadi. Ikaninso mabatire onse ndi memori khadi. Lumikizaninso chojambulira ku chotulukira magetsi. Dinani ndi kukanikiza batani lamphamvu kuti 3 masekondi, kenako masulani.
Nyali yobiriwira pa charger iyenera kuzimitsidwa pambuyo pake 10 masekondi. Yatsani chipangizocho podina ndi kukanikiza batani lamphamvu pafupifupi 5 masekondi. Ngati zina zonse zalephera, mutha kuyesanso kukhazikitsanso chipangizo chanu pogwira mabatani onse nthawi imodzi pafupifupi 10 masekondi.
Q9: How many mAh is the NOCO GB40?
The Noco GB40 genius BOOST gets 2150 mAh and 1000 A.
Mapeto
Ngati mukukumana ndi mavuto ndi chipangizo chanu cha Noco GB40, monga kusalipira kapena kudina phokoso, pali zinthu zingapo zomwe mungachite kuti mukonze. If all of above solutions fail, itha kukhala nthawi yoti mutenge Noco GB40 yanu kuti mukonze.