Hulkman jump starter error codes and solutions can be frustrating, but with a little knowledge, you can get your jump starter up and running again in no time. במאמר זה, we’ll go over the most common Hulkman jump starter error codes and what to do if you encounter one.
How to troubleshoot Hulkman jump starter error codes?
Hulkman jump starter error codes can be quite frustrating to troubleshoot. למרות זאת, with a little detective work, you can quickly identify and solve the issue. Here are some tips for troubleshooting Hulkman jump starter error codes:
- בדוק את רמות הסוללה. Make sure the battery is fully charged and that the jumper cables are connected properly.
- Check the output voltage. If the output voltage is low, בדוק אם הסוללה טעונה במלואה. If the voltage is still low, there may be a problem with the jump starter.
- Check the output current. If the output current is low, בדוק אם הסוללה טעונה במלואה. If the current is still low, there may be a problem with the jump starter.
- Check the jump starter’s fuse. אם הפתיל נשבר, the jump starter may not be able to start.
- Check the jump starter’s circuit breaker. If the circuit breaker is tripped, the jump starter may not be able to start.
- Check the jump starter’s ground. If the ground is not good, the jump starter may not be able to start.
Hulkman jump starter error code 1
HULKMAN products feature multiple advanced safety technologies, including reverse-polarity protection. It can detect a reverse attachment to your car battery automatically. If you reverse the polarity of the clamps, it will display the “Error Code 1/Error Code ” message as the above picture revealed.
If the screen shows “Error Code 1,” please follow these 3 steps:
- שלב 1: Take off and exchange the clamps. Recheck your car battery terminals: the red clamps connect to “+” and the black clamps to “-“;
- שלב 2: The screen will display the “READY” icon, following which you can go back to start your engine ignition.
- שלב 3: Remove the clamps from the car battery.
Hulkman jump starter error code 2
If there is a “Hulkman jump starter error code 2 ” on your screen, it means your car battery voltage is below 8V, and you might need to use the Force Start function.
There are 4 Steps to use the Force Start Function:
- שלב 1: Insert the battery clamps into the jump starter and attach the clamps to the car battery (The screen may display “Error Code 2” or nothing).
- שלב 2: Press the Power Button and Flashlight Button simultaneously for 2–3 seconds to start the force output.
- שלב 3: Start the car engine.
- שלב 4: Remove the clamps from the car battery.
Hulkman jump starter error code 3
If the screen shows “Error Code 3,” it means the jump starter is at an extremely low or high temperature, which is outside the range of operating temperature.
פlease follow these 5 steps:
- שלב 1: Remove the clamps from the car battery.
- שלב 2: Leave your devices in a shady place and wait for 10 minutes until the “Error Code 3” message disappears automatically.
- שלב 3: Reconnect the clamps to the car battery correctly and the “READY” icon will appear on screen.
- שלב 4: Start the car engine.
- שלב 5: Remove the clamps from the car battery
Hulkman jump starter error code 4
If the screen shows ‘Error Code 4’, it means the jump starter has entered the Safe Mode automatically.
Please follow these 3 steps:
- שלב 1: Remove the clamps from the car battery.
- שלב 2: Place the jump starter in a shady place and wait for 10 minutes until the “Error Code 4” message disappears automatically.
- שלב 3: Reconnect the clamps to the car battery correctly.
- שלב 4: Start the car engine.
- שלב 5: Remove the clamps from the car battery
What to do if Hulkman jump starter error codes occur?
If you’re getting error codes on your Hulkman jump starter, it means there’s a problem with the unit. The above is what you can do to troubleshoot and fix the issue. If you’re still getting error codes after trying these tips, contact Hulkman customer service([email protected]) for further assistance.
What to do if Hulkman jump starter doesn’t work?
אם שלך הולקמן קפיצה מתנע doesn’t seem to be working, יש כמה דברים שאתה יכול לעשות כדי לפתור את הבעיה.
- ראשון, check the battery connections. Make sure the battery is properly inserted into the jump starter and the positive and negative connectors are connected.
- הַבָּא, try to charge the battery. אם הסוללה טעונה במלואה, the jump starter may not be getting power from the battery.
- סוף כל סוף, check the cord. Make sure it is securely plugged into the jump starter and the outlet.
הסוף
לאחר קריאת המאמר הזה, you should now have a better understanding of the meaning of Hulkman jump starter error codes. If you are ever faced with one of these error codes, you should now know how to interpret them and what steps you need to take in order to fix the problem.