Hulkman jump starter error codes and solutions can be frustrating, but with a little knowledge, you can get your jump starter up and running again in no time. In hierdie artikel, we’ll go over the most common Hulkman jump starter error codes and what to do if you encounter one.
How to troubleshoot Hulkman jump starter error codes?
Hulkman jump starter error codes can be quite frustrating to troubleshoot. Egter, with a little detective work, you can quickly identify and solve the issue. Here are some tips for troubleshooting Hulkman jump starter error codes:
- Gaan die batteryvlakke na. Make sure the battery is fully charged and that the jumper cables are connected properly.
- Check the output voltage. If the output voltage is low, kyk of die battery ten volle gelaai is. If the voltage is still low, there may be a problem with the jump starter.
- Check the output current. If the output current is low, kyk of die battery ten volle gelaai is. If the current is still low, there may be a problem with the jump starter.
- Check the jump starter’s fuse. As die lont geblaas is, the jump starter may not be able to start.
- Check the jump starter’s circuit breaker. If the circuit breaker is tripped, the jump starter may not be able to start.
- Check the jump starter’s ground. If the ground is not good, the jump starter may not be able to start.
Hulkman jump starter error code 1
HULKMAN products feature multiple advanced safety technologies, including reverse-polarity protection. It can detect a reverse attachment to your car battery automatically. If you reverse the polarity of the clamps, it will display the “Error Code 1/Error Code ” message as the above picture revealed.
If the screen shows “Error Code 1,” please follow these 3 steps:
- Stap 1: Take off and exchange the clamps. Recheck your car battery terminals: the red clamps connect to “+” and the black clamps to “-“;
- Stap 2: The screen will display the “READY” icon, following which you can go back to start your engine ignition.
- Stap 3: Verwyder die klampe van die motorbattery.
Hulkman jump starter error code 2
If there is a “Hulkman jump starter error code 2 ” on your screen, it means your car battery voltage is below 8V, and you might need to use the Force Start function.
Daar is 4 Steps to use the Force Start Function:
- Stap 1: Plaas die batteryklemme in die springaansitter en heg die klemme aan die motorbattery (The screen may display “Error Code 2” or nothing).
- Stap 2: Druk die kragknoppie en flitsligknoppie gelyktydig vir 2–3 sekondes om die kraguitset te begin.
- Stap 3: Begin die motor enjin.
- Stap 4: Verwyder die klampe van die motorbattery.
Hulkman jump starter error code 3
If the screen shows “Error Code 3,” it means the jump starter is at an extremely low or high temperature, which is outside the range of operating temperature.
Please follow these 5 steps:
- Stap 1: Verwyder die klampe van die motorbattery.
- Stap 2: Leave your devices in a shady place and wait for 10 minutes until the “Error Code 3” message disappears automatically.
- Stap 3: Reconnect the clamps to the car battery correctly and the “READY” icon will appear on screen.
- Stap 4: Begin die motor enjin.
- Stap 5: Verwyder die klampe van die motorbattery
Hulkman jump starter error code 4
If the screen shows ‘Error Code 4’, it means the jump starter has entered the Safe Mode automatically.
Please follow these 3 steps:
- Stap 1: Verwyder die klampe van die motorbattery.
- Stap 2: Place the jump starter in a shady place and wait for 10 minutes until the “Error Code 4” message disappears automatically.
- Stap 3: Reconnect the clamps to the car battery correctly.
- Stap 4: Begin die motor enjin.
- Stap 5: Verwyder die klampe van die motorbattery
What to do if Hulkman jump starter error codes occur?
If you’re getting error codes on your Hulkman jump starter, it means there’s a problem with the unit. The above is what you can do to troubleshoot and fix the issue. If you’re still getting error codes after trying these tips, contact Hulkman customer service([email protected]) for further assistance.
What to do if Hulkman jump starter doesn’t work?
As jou Hulkman-springaansitter doesn’t seem to be working, daar is 'n paar dinge wat jy kan doen om die probleem op te los.
- Eerstens, check the battery connections. Make sure the battery is properly inserted into the jump starter and the positive and negative connectors are connected.
- Volgende, try to charge the battery. As die battery ten volle gelaai is, the jump starter may not be getting power from the battery.
- Uiteindelik, check the cord. Make sure it is securely plugged into the jump starter and the outlet.
Die einde
Na die lees van hierdie artikel, you should now have a better understanding of the meaning of Hulkman jump starter error codes. If you are ever faced with one of these error codes, you should now know how to interpret them and what steps you need to take in order to fix the problem.